Read + Write + Report
Home | Start a blog | About Orble | FAQ | Blogs | Writers | My Orble | Login

Valentine Glitter Heart Card #1

February 1st 2009 12:25
valentine card heart rhinestones beads glitter craft free card making instructions
Valentine Sparkle Heart Card #1


Materials Required:

1. White card 145mm x 290mm. Scored and folded in half to make a square base card.
2. Glitter heart approx 40mm wide. (For instructions on making the glitter hearts see my previous post Click here.
3. Piece of pink card 100mm x 100mm. (or other colour of your choice).
4. Punch Wheel.
5. Ruler
6. Piece of graph paper 145mm x 145mm, with 1mm graduations marked.
7. Pencil
8. Craft knife and paper trimmer
9. Sewing pin
10. Double Sided Sticky Tape (DSST)

Instructions

Making the window in the card front:

1. Cut the graph paper so it is a 145mm x 145mm square. (This will fit exactly onto the front of your card).

2. Measure in 37mm from each of the square and draw a line parallell to each edge, The four lines will intersect to make a smaller square.



3. Open out the base, and place the graph paper over the front section.
Using the sewing pin, make a small hole in each of the corners of the square, as indicated by the arrows in the picture above.

These holes are to be a marker so you know where to cut the window in your card front, ensuring that it is centrally placed, and the exact size required.


4. Using a craft knife, cut the square from the front of your card, using the four pin holes as a guide to the corners of the square. Do not throw away the piece of card you have cut out.

5. Take the small square the you cut from the card front, and trim 20mm from the top ,and 20mm from one side. (Making a square 49mm x 49mm).

6. Run the punch wheel around the edge of this square, approx 2mm in from the edge. Then punch wheel around the square that you cut in the front of the card, approx 2mm in from the cut edge.

7. Using DSST attach the Glitter heart centrally to the small white square.

8. Attach the piece of pink (or colour of your choice) card 100mm x 100mm to the inside of the card's front using DSST. Make sure that it completely covers the hole you cut out.

9. Using DSST, attach the small white piece of card with the glitter heart centrally into the pink square on the front of your card.




66
Vote


   

   

   


Add A Comment

To create a fully formatted comment please click here.


CLICK HERE TO LOGIN | CLICK HERE TO REGISTER

Name or Orble Tag
Home Page (optional)
Comments
Bold Italic Underline Strikethrough Separator Left Center Right Separator Quote Insert Link Insert Email
Notify me of replies
Notify extra people about this comment
Is this a private comment?
List the Email Addresses or Orble Tags of the people you would like to be notified about this comment


One per line max of 30

List the Email Addresses or Orble Tags of the people you would like to be notified about this private comment thread. Only the people in this list will be able to see or reply to your comment.


One per line max of 30

Your Name
(for the email going out to the above list, it can be different to your Orble Tag)
Your Email Address
(optional)
(required for reply notification)
Submit
More Posts
9 Posts
4 Posts
1 Posts
77 Posts dating from April 2008
Email Subscription
Receive e-mail notifications of new posts on this blog:
0

Jude O'Connell's Blogs

2913 Vote(s)
19 Comment(s)
48 Post(s)
Moderated by Jude O'Connell
Copyright © 2006 2007 2008 On Topic Media PTY LTD. All Rights Reserved. Design by Vimu.com.
On Topic Media ZPages: Sydney |  Melbourne |  Brisbane |  London |  Birmingham |  Leeds     [ Advertise ] [ Contact Us ] [ Privacy Policy ]